HiFocus 130 Plus

HiFocus 130 Plus

Plasma Cutting System HiFocus 130 PLUS

  • Plasma cutting of all electrically conductive materials between 0.5 and 40 mm material thickness with the Contour Cut technology
  • Recommended cutting range from 0.5 up to 32 mm material thickness
  • Maximum piercing 25 mm
  • Cutting and marking without change of plasma torch and consumables, by using the plasma gas control unit FlowControl, also on coated materials
  • Cost-saving alternative to laser cutting with less than one fourth of the investment and operating costs
  • CNC-controlled cutting with machine torch and optional use of oxygen, nitrogen or argon/hydrogen as plasma gas
  • CNC interface for all kinds of 2D and 3D CNC guiding systems
  • Contour Cut guarantees high repeatability and dimension accuracy of the cut parts
  • Low squareness and inclination tolerances of the cut surfaces
  • Precise contours when cutting sharp edges and small radii
  • Cutting of holes with small diameters in mild steel
  • High lifetime of consumables due to dual gas ignition and nozzle saving piercing with swirl gas technology

Power Source HiFocus 130 PLUS

  • Optimum process flow due to microprocessor control
  • Monitoring of the process sequences (torch cooling, ignition time, pilot arc time, short circuit time during torch ignition, power source etc.)
  • Display of operating modes and error message by LED and display
  • Extensive interface for adaption to CNC-control
  • Serial data transfer to PC for diagnostic purposes
  • Stepless cutting current setting from 20 to 130 A
  • Optimum piercing by stepless time delay for main arc and adjustable upslope in 4 steps
  • Adjustable down-slope at corner, start and end signals of the guiding system
  • Digital display of current and voltage
  • Automatic display of pre-selected cutting current
  • Marking current 16 A

Contour Cut and Contour Cut Speed

  • Optimized plasma cutting technologies for cutting contours in mild steel
  • Precise plasma cutting of small contours and holes 1:1 with Contour Cut
  • Cutting of large contours up to 50 % faster with Contour Cut Speed
  • High cut quality and contour accuracy
  • Reduced angular deviations and improved quality of cut surfaces
  • Very high repeatability and dimension accuracy
  • No time-consuming after-treatment – high productivity at low costs
  • Standard for all HiFocus systems – no further equipment

Plasma Torch PerCut 201/211

  • Plasma machine torch PerCut 201 for standard applications as well as for high-precision bevel cutting
  • Quick-change torch PerCut 211 with thread for a quick and handy installation of the torch
  • Special torches like robot version, short or/and inclined versions, are available for special applications
  • Higher cutting speeds reduce the costs per cutting meter
  • Long lifetime of consumables saves resources
  • Narrower cutting kerfs and, therefore, less emissions and waste
  • Significantly lower gas consumption compared to competitive products due to more effective liquid cooling system
  • Due to lower gas consumption comparatively low noise level
  • Bevel cutting up to 50 degrees with standard consumables
  • Cutting and marking with the same consumables

Gas Control Unit

Automatic plasma gas control unit FlowControl 2 consisting of plasma gas valve unit (PGV) and plasma gas controller (PGC) for automatic gas flow control according to the material quality and thickness via databases installed in the PGC or the CNC guiding system.

 

 POWER SOURCE   HiFocus 130
         
Mains Voltage   3 x 400 V; 50 Hz    
Cutting Range          
  • Maximum
  40 mm        
  • Recomended
  0.5 - 32 mm        
Connecting Power ( At 250 A )   32 kVA (100% d. c.)        
Mains fuses(slow-blow)   50 A
Mains frequency   50 Hz / 60 Hz
Protection Class   IP 22
Open Circuit Voltage   400 V ( DC )
Weight 251 kg
Cutting Current 20 – 130 A (100 % d. c.)
Cooling Kjellfrost
Dimensions( LxWxH ) 960 x 540 x 1050 mm
 Max Piercing   25 mm
 Marking Current  16 A
 Plasma machine torch PerCut 201
Quick-change torch PerCut 211
Clamping diameter  50.8 mm
Plasma gases O2, N2, Ar/H2
Marking gases Ar
Swirl gases O2, N2, Air, N2/H2 (F5)
   
No Data